You are here

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

Comments

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

Hello! My name is Monica, and I want to share my impressions of playing in online casinos. I've been looking for a long time for entertainment that could be combined with my busy schedule, and I finally found the perfect option. Andromeda Casino https://andromeda.casinologinaustralia.comThe casino website turned out to be very convenient and easy to use. Registration took only a couple of minutes, and I immediately received a nice bonus on my first deposit. The games here are simply amazing! 

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

The '51 Facts About Chernobyl' blog post on https://chernobylstory.com/blog/51-fact-about-chernobyl/ was an eye-opener. From the pre-accident ambitions of making Chernobyl one of the world's most powerful nuclear plants to the post-disaster realities and the intriguing untold stories of the zone, the article covered it all. Learning about the Duga-1 radar, the role of Pripyat, and the ongoing impact of the disaster was enlightening.

Bylo horké léto a já hledal něco zajímavého. Chtěl jsem zkusit něco nového, a tak jsem se obrátil na sázení. Když jsem navštívil webové stránky MostBet, viděl jsem spoustu příležitostí k sázení na kanceláře. Zvláště se mi líbily různé bonusy, které stránka nabízí: od sázek zdarma až po bonusy za vklad. Díky tomu byl můj volný čas nejen zajímavý, ale také výnosný.

 

"Integrate multiple VESC (Vedder Electronic Speed Controller) units via CAN-Bus for synchronized control in electric vehicle systems. Utilizing Controller Area Network (CAN) communication protocol ensures efficient real-time data exchange between VESCs, enabling coordinated motor control and advanced functionalities. With CAN-Bus, each VESC acts as a node, facilitating seamless integration and synchronization of motor speed, torque, and other parameters across the network with proposed idea for thesis writing . This allows for precise control and optimization of electric propulsion systems, enhancing performance, reliability, and overall vehicle efficiency in applications such as electric cars, drones, and robotics."

As someone who plays high stakes, I appreciate the variety of slots at Slots City https://slotscity.ua/ru/slots that cater to players like me. The progressive jackpots and high-limit games offer the excitement and the potential rewards I look for. The smooth gameplay and quick payouts make it my top choice.

As a student tasked with choosing a research paper topic, I often found myself overwhelmed by the sheer number of options. EssayHub's comprehensive list of research paper topics https://essayhub.com/blog/research-paper-topics came to my rescue, offering a diverse range of intriguing ideas across various disciplines. Whether I was interested in science, history, literature, or social issues, EssayHub had a topic that piqued my curiosity. The article provided valuable insights and inspiration, making the daunting task of topic selection much more manageable. Thanks to site, I found the perfect research paper topic that aligned with my interests and academic goals.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller


Submitted by frank on Tue, 2017-10-03 19:50

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.




Looking for a place where you can realize your desire and need for excitement? Then https://q7-casino.casinologinaustralia.com is your perfect choice among the many casinos in Australia. Their games are not only exciting but also fair, giving you a fair chance of winning. Don't miss your chance to win big, because anything is possible if you visit the site right now. This could be the best decision of your life.

Here in Brazil, the weather can be quite unpredictable. I've tried various weather sites, but none of them were quite accurate. Then, I stumbled upon this one and it's been a lifesaver. It gives me accurate weather updates for my city. Just follow this link: https://climatempo.info/36797/estancia-grande. Now, I can finally plan my day without worrying about sudden rain showers.

I've been on an incredible journey through the realm of online gaming, and I tell you, it's been an eye-opener. The sheer abundance and variety of games I discovered on

box24 casino blew me away. It doesn't matter if you're a newcomer or a seasoned player; navigating through the platform is a walk in the park, thanks to its super intuitive interface. For us folks down here in Australia, this is a massive leap forward. The level of excitement it provides is simply unmatched. Don’t just take my word for it, check it out yourself right here. Trust me, it's worth it.

Shalom para todos! Recentemente, estava a pensar em como passar o meu tempo nos fins-de-semana e precisava de encontrar algo novo. Aconselharam-me a procurar um casino online e encontrei o casinos em portugal . Este site é muito fácil de utilizar, tem muitos jogos diferentes para todos os gostos e rapidamente encontrei o que me agradava. Gostei do facto de ser fácil começar a jogar e de não haver configurações complicadas. Foi uma óptima maneira de me divertir e fazer uma pausa na minha rotina diária.

Hey everyone! I was looking for a fun and engaging way to spend my free time and found an incredible site. I wanted a place where I could play games and have a chance to win something. That’s how I discovered aus88 casino from Australia. The site has a huge selection of games and slots, which is perfect for someone who likes variety. The bonuses are fantastic too. They offer a welcome bonus for new players and regular promotions for everyone. The site’s interface is user-friendly, making it easy to find what you’re looking for.

Running an NGO that supports environmental projects in Brazil means I often need to send money there. I needed a service that was both transparent and had minimal fees to ensure the maximum amount of our funding went directly to the projects. I found transfer money to brazil and it fit the bill perfectly. The site is easy to navigate, offers clear information on fees and exchange rates, and provides special deals like loyalty discounts for regular users. Using this service has allowed us to increase the efficiency of our financial operations, ensuring more funds are used for direct action rather than administrative costs.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller

 

 
Submitted by frank on Tue, 2017-10-03 19:50

 

Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.


In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.

Make sure to use the latest VESC-Tool version!

Download from http://www.vesc-project.com/vesc_tool


Vesc-Tool_ISW_Twin VESC_intro


Vesc-Tool_ISW_Twin VESC_wiring


Important Notice:

Run the Motor Setup Wizard on each VESC first.

Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM).  Use CAN-Bus instead.

Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected. 

Failing to follow these instructions may damage your VESC (s) permanently.


Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.

Connect your master VESC® to your computer using a mini/micro USB cable.

Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.

Run the VESC®-Tool software.


 

Vesc-Tool_ISW_connect

 


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_Twin VESC_master

 


Vesc-Tool_ISW_Set ID Master


Vesc-Tool_ISW_select ppm


Vesc-Tool_ISW_current no reverse brake

This is the next screen you will see.


Vesc-Tool_ISW_mapping_01


Vesc-Tool_ISW_mapping_02


Vesc-Tool_ISW_mapping_03


Vesc-Tool_ISW_mapping_04


Vesc-Tool_ISW_mapping_05


Vesc-Tool_ISW_mapping_06


Vesc-Tool_ISW_disconnect master


Now we will configure the slave VESC.

Plug your USB-Cable into the slave VESC.  Make sure both VESCs are powered up and connected via CAN bus cable.


Vesc-Tool_ISW_connect


Vesc-Tool_ISW_welcome


Vesc-Tool_ISW_load default


Vesc-Tool_ISW_select slave


 Vesc-Tool_ISW_Twin VESC_slave ID


Vesc-Tool_ISW_Twin VESC_finisch_slave


Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.

Adjustments for the input device (App settings) are configured on the master VESC.

Barbecue takeout requires the right packaging, and the 0.25 Gallon BBQ Foil Bag from SafePro has been excellent. I came across this product while browsing McDonald Paper's website. You can see it at https://mcdonaldpaper.com/safepro-bbq1-4-0-25-gallon-bbq-foil-bag-1000-cs/ . These foil bags are perfect for keeping the BBQ fresh and hot. They’re easy to use and ensure the food remains flavorful, making them ideal for our takeout orders.

The other day, I discovered an online platform that's a real gem 

https://betvisa-loginbd.com/bonuses/ for us here in Bangladesh. It offers an exciting range of games and a user-friendly interface that makes the experience truly engaging. You can check it out at this link. Trust me, once you do, you'll see why I'm so enthusiastic about it!

I've been on a quest for top-notch online gaming experiences, and it seems like my journey has finally come to an end. I stumbled upon a site that is a complete game-changer. The game selection is immense and the platform is remarkably user-friendly. The

mSport Bet section particularly caught my attention. It feels like it's crafted especially for

Nigeria gamers like us! Believe me, it's a place where excitement meets convenience. Give it a try here and experience the thrill yourself!

FNF Online community is active on social media, where players share their experiences, tips, and fan creations. This online presence keeps the community connected and engaged, enhancing the overall experience.

Living in Kesh, a region known for its scenic beauty, accurate weather updates are vital for my everyday life. I found this fantastic resource 

https://meteo.uk/22946/kesh here that has brought a significant improvement to my daily scheduling. More than just basic temperature forecasts, the detailed analysis offered is incredibly precise. This is especially handy when planning outdoor activities. My understanding of local weather patterns has never been this easy and it has revolutionized my life as a resident of Kesh. I highly recommend it for anyone seeking reliable weather updates.

Hello, mates! If you're in Australia and looking for a reliable online casino, check out Yoju Casino . The casino offers an impressive array of games, including many themed slots that are a big hit. They also offer weekly tournaments which are a lot of fun and a great way to test your skills against other players. The support team is very proactive and withdrawals are processed quickly, so you're never left waiting.

I've always been curious about how sunglasses protect our eyes from glare. Luckily, I found this insightful piece here 

https://optyx.com/uncategorized/combating-glare-with-technology-the-role-of-polarization-in-sunglasses/ that explained all about the role of polarization. It's a great resource and I highly recommend checking it out.

Setting up multiple VESCs via CAN-Bus using a PPM signal radio controller offers a sophisticated and efficient way to control multiple motors in electric vehicles. By following the proper configuration steps and utilizing the right tools, you can create a reliable and high-performance system for your project.

Best,

Aimee - greek food truck

Setting up multiple VESCs via CAN-Bus using a PPM signal radio controller offers a sophisticated and efficient way to control multiple motors in electric vehicles. By following the proper configuration steps and utilizing the right tools, you can create a reliable and high-performance system for your project.

Setting up multiple VESCs via CAN-Bus using a PPM signal radio controller offers a sophisticated and efficient way to control multiple motors in electric vehicles. By following the proper configuration steps and utilizing the right tools, you can create a reliable and high-performance system for your project.

Setting up multiple VESCs via CAN-Bus using a PPM signal radio controller offers a sophisticated and efficient way to control multiple motors in electric vehicles. By following the proper configuration steps and utilizing the right tools, you can create a reliable and high-performance system for your project.

Pages