You are here
Feature Requests
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Read erpm of motor through motor tachometer by jordanlow » Tue, 2019-04-30 15:18 |
1 |
by Teslafly Sat, 2019-07-20 00:44 |
|
|
Remap Rotary Encoder Input to CAN (or other) by Artemis Skade » Wed, 2020-04-01 20:23 |
0 |
by Artemis Skade Wed, 2020-04-01 20:23 |
|
|
Renaming the versions to avoid confusion when downloading. by ThierryGTLTS » Fri, 2017-09-08 12:54 |
4 |
by ThierryGTLTS Sun, 2017-10-15 19:02 |
|
|
Request Feature to add minimum Battery Voltage value in addition to duty cycle for field weakening by aquaponiccowboy » Mon, 2022-10-17 04:49 |
0 |
by aquaponiccowboy Mon, 2022-10-17 04:50 |
|
|
Reverse safety function by rich » Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
|
|
safety switch by Ralph Luckwaldt » Mon, 2019-10-21 13:15 |
1 |
by frank Mon, 2019-10-21 20:58 |
|
|
Sensorless temperature compensation by ESCam » Fri, 2018-12-14 19:38 |
3 |
by Roby_88 Sat, 2023-03-11 17:39 |
|
|
Servo Motor position control by wdaehn » Wed, 2017-11-29 21:45 |
0 |
by wdaehn Wed, 2017-11-29 21:45 |
|
|
Set legal speed 20 km/h using reverse pin input by Dominator2 » Sun, 2023-06-18 12:45 |
2 |
by vadicus Thu, 2023-10-26 01:20 |
|
|
Setting an ERPM limit for one motor based off another motors ERPM by NijiflianBustock » Fri, 2023-07-07 18:37 |
0 |
by NijiflianBustock Fri, 2023-07-07 18:37 |
|
|
Setting the minimum ERPM in FOC mode? by mathias » Sat, 2018-06-16 02:20 |
0 |
by mathias Sat, 2018-06-16 02:20 |
|
|
Show actual encoder RPM by Enak » Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
|
|
SINE/COSINE Encoder Support by shaman » Mon, 2018-12-17 15:14 |
11 |
by larsrocket Thu, 2025-04-17 23:37 |
|
|
Single shunt by andreas » Wed, 2018-09-12 22:17 |
0 |
by andreas Wed, 2018-09-12 22:17 |
|
|
Sinusoidal commutation by shaman » Wed, 2020-06-03 23:42 |
0 |
by shaman Wed, 2020-06-03 23:42 |
|
|
Some ideas to improve VESC by e-biker » Sun, 2018-03-18 16:36 |
3 |
by Roger Wolff Mon, 2018-04-23 08:57 |
|
|
Some small problems with the VESC 6 and the VESC Tool V 0.87 by JL2579 » Thu, 2018-01-11 16:27 |
2 |
by JL2579 Tue, 2018-01-16 16:58 |
|
|
Speed mode with zero speed hold by mpalamar » Thu, 2025-10-09 16:15 |
3 |
by Matevz Wed, 2025-11-19 10:54 |
|
|
SpeedControl - Slew Rate? by NickN » Wed, 2020-10-07 20:13 |
1 |
by NickN Wed, 2020-10-07 20:28 |
|
|
Stand alone FOC fork? by lizardmech » Sat, 2018-03-03 17:18 |
22 |
by arvidb Wed, 2018-03-07 18:01 |
|
|
Standby - consumption when battery is conencted by derbe » Thu, 2019-09-26 14:07 |
4 |
by frank Mon, 2020-01-27 20:48 |
|
|
Steering channel (dual vesc setup via CAN bus) by fender90 » Sun, 2020-04-26 03:47 |
0 |
by fender90 Sun, 2020-04-26 03:47 |
|
|
Support for AMC1301 powered from bootstrap by antonchromjak » Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
|
|
Total ODOMETER counter via real time logging feature request by janzobanzo7 » Mon, 2022-10-24 14:49 |
6 |
by Lennart Duijn Fri, 2023-08-11 18:38 |
|
|
Traction control with different motors by Ba1tuks » Sun, 2020-05-31 15:10 |
2 |
by Mansens88 Mon, 2025-02-24 01:45 |
Log in to post new content in the forum.
