You are here
Feature Requests
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Dshot and uavcan protocol support by Roadead » Wed, 2021-09-08 06:09 |
0 |
by Roadead Wed, 2021-09-08 06:09 |
|
|
How to control a vesc controller without pulling electric wires on a bike? by peignier jacques » Sat, 2020-04-11 09:20 |
0 |
by peignier jacques Sat, 2020-04-11 09:21 |
|
|
Steering channel (dual vesc setup via CAN bus) by fender90 » Sun, 2020-04-26 03:47 |
0 |
by fender90 Sun, 2020-04-26 03:47 |
|
|
PAS and ADC (minimum input) by velolac » Sun, 2022-01-02 17:30 |
0 |
by velolac Sun, 2022-01-02 17:30 |
|
|
Dual control loop with magnetic encoders by wall0069 » Sun, 2019-06-02 05:39 |
0 |
by wall0069 Sun, 2019-06-02 05:39 |
|
|
AVERAGE ERPM (Max) Setting for dual vescs by Paul15578 » Fri, 2018-01-12 03:04 |
0 |
by Paul15578 Fri, 2018-01-12 03:04 |
|
|
uROS support by neuromancer2701 » Wed, 2019-11-06 21:17 |
0 |
by neuromancer2701 Wed, 2019-11-06 21:17 |
|
|
Setting the minimum ERPM in FOC mode? by mathias » Sat, 2018-06-16 02:20 |
0 |
by mathias Sat, 2018-06-16 02:20 |
|
|
Defining when Watt-hour / Amp-hour Data are rezeroed by isabar » Sun, 2018-06-24 10:19 |
0 |
by isabar Sun, 2018-06-24 10:19 |
|
|
Raw encoder output from UART by sprockmonty » Mon, 2018-08-13 16:45 |
0 |
by sprockmonty Mon, 2018-08-13 16:45 |
|
|
Foc openloop soft start by Alan oldguy » Fri, 2018-09-07 03:05 |
0 |
by Alan oldguy Fri, 2018-09-07 03:05 |
|
|
Enhance position and rpm control interface / protocol by brushlessjoe » Wed, 2019-03-20 21:54 |
0 |
by brushlessjoe Wed, 2019-03-20 21:54 |
|
|
Hallsensor by seketti » Fri, 2025-04-04 14:40 |
0 |
by seketti Fri, 2025-04-04 14:40 |
|
|
Vesc tool android app Autoconnect to last bluettoth vesc and automatic logging by mrendu43 » Mon, 2022-07-25 13:16 |
0 |
by mrendu43 Mon, 2022-07-25 13:16 |
|
|
Bafang BBSHD hub motor setup by csev-tcejorp » Sat, 2022-08-13 14:50 |
0 |
by csev-tcejorp Sat, 2022-08-13 14:50 |
|
|
IMU and balancing powertrain by sunsam8 » Thu, 2020-09-03 05:03 |
0 |
by sunsam8 Thu, 2020-09-03 05:03 |
|
|
Adding Openloop Com Comand and Temp. Measurement via Resistance by JulianT » Mon, 2022-10-03 11:32 |
0 |
by JulianT Mon, 2022-10-03 11:32 |
|
|
Electric scooter controller by saenz4931@gmail.com » Thu, 2020-09-10 05:58 |
0 |
by saenz4931@gmail.com Thu, 2020-09-10 05:58 |
|
|
controller_id on COMM_GET_IMU_DATA by andrea.scipione » Sun, 2020-11-22 19:07 |
0 |
by andrea.scipione Sun, 2020-11-22 19:07 |
|
|
Setting an ERPM limit for one motor based off another motors ERPM by NijiflianBustock » Fri, 2023-07-07 18:37 |
0 |
by NijiflianBustock Fri, 2023-07-07 18:37 |
|
|
Natural Braking by e-nduro » Thu, 2020-12-17 17:23 |
0 |
by e-nduro Thu, 2020-12-17 17:23 |
|
|
use PPM-modes with ADC by zoru24 » Mon, 2023-08-14 11:17 |
0 |
by zoru24 Mon, 2023-08-14 11:17 |
|
|
ADC out of bounds voltage still maps?! by Matt6288 » Tue, 2021-01-12 02:27 |
0 |
by Matt6288 Tue, 2021-01-12 02:27 |
|
|
Electric Mower Blade Speed by moose09876 » Tue, 2024-05-28 20:38 |
0 |
by moose09876 Tue, 2024-05-28 20:38 |
|
|
Dronecan 1036.StatusExtended message for motor temp by cjmssmd » Wed, 2024-09-04 02:05 |
0 |
by cjmssmd Wed, 2024-09-04 02:05 |
Log in to post new content in the forum.
