You are here
Feature Requests
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Force Sensor for a e-skateboard by beadon » Sat, 2022-06-04 05:08 |
1 |
by frank Sat, 2022-06-04 11:24 |
|
|
Custom Application Programming Through VESC TOOL by William Stanley » Mon, 2020-08-10 14:50 |
1 |
by William Stanley Mon, 2020-08-10 14:54 |
|
|
SpeedControl - Slew Rate? by NickN » Wed, 2020-10-07 20:13 |
1 |
by NickN Wed, 2020-10-07 20:28 |
|
|
ERPM Limit Update Over CAN by josh » Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
|
|
ADC Throttle Redundancy by bgdwiepp » Mon, 2020-01-20 09:18 |
1 |
by frank Mon, 2020-01-27 20:42 |
|
|
Add another motor temperature sensor type (only minor tweak needed) by Henque19 » Wed, 2020-01-29 21:25 |
1 |
by Henque19 Wed, 2020-03-25 11:31 |
|
|
Set legal speed 20 km/h using reverse pin input by Dominator2 » Sun, 2023-06-18 12:45 |
2 |
by vadicus Thu, 2023-10-26 01:20 |
|
|
Adding a Openloop COMM Comand This topic has been moved to "General discussion" (View topic) |
|||
|
About motor closed loop angular velocity control by Roberto00 » Wed, 2021-04-07 02:18 |
2 |
by Offline Wed, 2021-05-05 07:57 |
|
|
Support for AMC1301 powered from bootstrap by antonchromjak » Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
|
|
Some small problems with the VESC 6 and the VESC Tool V 0.87 by JL2579 » Thu, 2018-01-11 16:27 |
2 |
by JL2579 Tue, 2018-01-16 16:58 |
|
|
Motion commands for controlling CNCs by andresv » Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
|
|
Traction control with different motors by Ba1tuks » Sun, 2020-05-31 15:10 |
2 |
by Mansens88 Mon, 2025-02-24 01:45 |
|
|
Dual signal on throttle by tmgofer » Mon, 2023-11-20 09:00 |
2 |
by vadicus Thu, 2024-06-27 07:51 |
|
|
Cruise control speed reduction by dsuresh » Mon, 2021-03-01 20:40 |
2 |
by dsuresh Wed, 2021-06-30 21:31 |
|
|
Better use of hall sensors. by ThierryGTLTS » Fri, 2017-10-20 17:18 |
2 |
by AfdhalAtiffTan Wed, 2018-10-24 02:16 |
|
|
Deceleration Curve by slick » Sun, 2019-07-21 21:10 |
2 |
by kylerlaird Thu, 2021-01-21 17:31 |
|
|
Bluetooth "ignition key" by topiaskorpi » Wed, 2019-10-16 18:47 |
2 |
by Ralphvince Thu, 2025-07-17 08:35 |
|
|
high speed mode -- 100% PWM duty cycle and over-modulation by RSR » Sun, 2018-06-17 12:21 |
2 |
by frank Mon, 2025-02-24 09:16 |
|
|
Show actual encoder RPM by Enak » Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
|
|
adding electronic freewheel function by ceejaye » Mon, 2019-09-02 17:30 |
3 |
by mnmsmushy Wed, 2020-09-23 02:32 |
|
|
Some ideas to improve VESC by e-biker » Sun, 2018-03-18 16:36 |
3 |
by Roger Wolff Mon, 2018-04-23 08:57 |
|
|
Limp mode via CAN by totalgeek9224 » Mon, 2020-02-10 14:37 |
3 |
by A2 Wed, 2021-09-08 21:20 |
|
|
Reverse safety function by rich » Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
|
|
Add support for dual H3LIS331DL accelerometer by SirPolPol » Fri, 2022-04-08 09:09 |
3 |
by frank Mon, 2022-04-11 09:08 |
|
Log in to post new content in the forum.
