You are here
Feature Requests
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Reverse safety function by rich » Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
|
|
cPPM APP with mixing by Enak » Wed, 2017-09-06 00:54 |
1 |
by benjamin Wed, 2017-09-06 23:25 |
|
|
Not too much features, and clean, tidy software. by ThierryGTLTS » Fri, 2017-09-08 13:10 |
0 |
by ThierryGTLTS Fri, 2017-09-08 13:10 |
|
|
Renaming the versions to avoid confusion when downloading. by ThierryGTLTS » Fri, 2017-09-08 12:54 |
4 |
by ThierryGTLTS Sun, 2017-10-15 19:02 |
|
|
watt mode by Willoz600 » Tue, 2017-10-10 09:26 |
1 |
by frank Mon, 2017-10-16 20:58 |
|
|
Profile management for Mobile apps by emmaanuel » Tue, 2017-10-17 20:54 |
5 |
by Cledus Wed, 2017-10-25 15:54 |
|
|
PID speed control in ADC-app by GunnarW » Wed, 2017-10-25 20:49 |
1 |
by benjamin Fri, 2017-10-27 21:39 |
|
|
Commutation sync by TechAUmNu » Mon, 2017-11-20 17:40 |
1 |
by benjamin Wed, 2017-11-22 11:12 |
|
|
Servo Motor position control by wdaehn » Wed, 2017-11-29 21:45 |
0 |
by wdaehn Wed, 2017-11-29 21:45 |
|
|
AVERAGE ERPM (Max) Setting for dual vescs by Paul15578 » Fri, 2018-01-12 03:04 |
0 |
by Paul15578 Fri, 2018-01-12 03:04 |
|
|
Some small problems with the VESC 6 and the VESC Tool V 0.87 by JL2579 » Thu, 2018-01-11 16:27 |
2 |
by JL2579 Tue, 2018-01-16 16:58 |
|
|
Enhance sensorless FOC using phase vsense? by lizardmech » Tue, 2018-02-27 17:39 |
5 |
by lizardmech Wed, 2018-02-28 14:36 |
|
|
Stand alone FOC fork? by lizardmech » Sat, 2018-03-03 17:18 |
22 |
by arvidb Wed, 2018-03-07 18:01 |
|
|
Some ideas to improve VESC by e-biker » Sun, 2018-03-18 16:36 |
3 |
by Roger Wolff Mon, 2018-04-23 08:57 |
|
|
Setting the minimum ERPM in FOC mode? by mathias » Sat, 2018-06-16 02:20 |
0 |
by mathias Sat, 2018-06-16 02:20 |
|
|
Defining when Watt-hour / Amp-hour Data are rezeroed by isabar » Sun, 2018-06-24 10:19 |
0 |
by isabar Sun, 2018-06-24 10:19 |
|
|
Configurable Beta factor for motor NTC. by Danny Bokma » Tue, 2017-09-05 21:29 |
11 |
by slapshot136 Sun, 2018-07-15 20:05 |
|
|
15S support (and more amps) by Torxed » Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
|
|
Raw encoder output from UART by sprockmonty » Mon, 2018-08-13 16:45 |
0 |
by sprockmonty Mon, 2018-08-13 16:45 |
|
|
Ramping and idle control by dougm » Sat, 2018-09-01 16:22 |
0 |
by dougm Sat, 2018-09-01 16:22 |
|
|
Foc openloop soft start by Alan oldguy » Fri, 2018-09-07 03:05 |
0 |
by Alan oldguy Fri, 2018-09-07 03:05 |
|
|
Single shunt by andreas » Wed, 2018-09-12 22:17 |
0 |
by andreas Wed, 2018-09-12 22:17 |
|
|
Show actual encoder RPM by Enak » Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
|
|
Better use of hall sensors. by ThierryGTLTS » Fri, 2017-10-20 17:18 |
2 |
by AfdhalAtiffTan Wed, 2018-10-24 02:16 |
|
|
Vesc slow speed BLDC without coging by igisboard » Tue, 2018-10-09 18:38 |
1 |
by Dillon Mon, 2018-11-19 01:41 |
Log in to post new content in the forum.
