You are here
Feature Requests
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Allow braking to override negative ramping time by Paul15578 » Wed, 2018-01-24 06:20 |
5 |
by benjamin Sat, 2019-02-23 10:14 |
|
|
Standby - consumption when battery is conencted by derbe » Thu, 2019-09-26 14:07 |
4 |
by frank Mon, 2020-01-27 20:48 |
|
|
Auto power shut down by Ecyclist » Thu, 2018-09-20 00:47 |
4 |
by sam.vanratt Sat, 2018-11-24 20:12 |
|
|
Renaming the versions to avoid confusion when downloading. by ThierryGTLTS » Fri, 2017-09-08 12:54 |
4 |
by ThierryGTLTS Sun, 2017-10-15 19:02 |
|
|
Trapezoidal Trajectory/Position Control by wewa » Sun, 2018-09-23 11:33 |
4 |
by ncbanse Thu, 2023-04-20 21:26 |
|
|
C Type USB and Power Delivery 3.1 by Rarikao » Fri, 2023-04-21 08:51 |
4 |
by vadicus Fri, 2023-04-28 05:30 |
|
|
Kill switch feature through adc input by Heddan99 » Sun, 2021-03-07 12:54 |
4 |
by frank Thu, 2021-06-10 14:18 |
|
|
PWM encoder support by Ieton2hahw » Fri, 2021-06-18 05:47 |
4 |
by electricfox Tue, 2025-04-08 10:54 |
|
|
PAS sensor for pedelec and speed pedelec by th0masrtg » Sun, 2020-04-26 08:55 |
4 |
by th0masrtg Thu, 2020-10-29 07:38 |
|
|
adding electronic freewheel function by ceejaye » Mon, 2019-09-02 17:30 |
3 |
by mnmsmushy Wed, 2020-09-23 02:32 |
|
|
Some ideas to improve VESC by e-biker » Sun, 2018-03-18 16:36 |
3 |
by Roger Wolff Mon, 2018-04-23 08:57 |
|
|
Limp mode via CAN by totalgeek9224 » Mon, 2020-02-10 14:37 |
3 |
by A2 Wed, 2021-09-08 21:20 |
|
|
Reverse safety function by rich » Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
|
|
Wand odometer by hans_maier » Sat, 2019-09-14 15:20 |
3 |
by gianni Mon, 2019-09-23 15:19 |
|
|
Sensorless temperature compensation by ESCam » Fri, 2018-12-14 19:38 |
3 |
by Roby_88 Sat, 2023-03-11 17:39 |
|
|
Lights control from the nrf remote/The WAND and configuration tab in VESC TOOL by ma-j-sterelektron » Thu, 2019-03-21 15:18 |
3 |
by ma-j-sterelektron Tue, 2020-02-18 15:00 |
|
|
Speed mode with zero speed hold by mpalamar » Thu, 2025-10-09 16:15 |
3 |
by Matevz Wed, 2025-11-19 10:54 |
|
|
Emergency Brake. by Solid_37 » Fri, 2020-07-03 22:43 |
3 |
by skyline1970 Mon, 2022-03-14 08:53 |
|
|
External speed sensor by Victor Bruun » Thu, 2021-02-04 08:59 |
3 |
by czndl Thu, 2021-11-25 21:33 |
|
|
Add support for dual H3LIS331DL accelerometer by SirPolPol » Fri, 2022-04-08 09:09 |
3 |
by frank Mon, 2022-04-11 09:08 |
|
|
Some small problems with the VESC 6 and the VESC Tool V 0.87 by JL2579 » Thu, 2018-01-11 16:27 |
2 |
by JL2579 Tue, 2018-01-16 16:58 |
|
|
Motion commands for controlling CNCs by andresv » Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
|
|
Support for AMC1301 powered from bootstrap by antonchromjak » Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
|
|
Set legal speed 20 km/h using reverse pin input by Dominator2 » Sun, 2023-06-18 12:45 |
2 |
by vadicus Thu, 2023-10-26 01:20 |
|
|
Adding a Openloop COMM Comand This topic has been moved to "General discussion" (View topic) |
|||
Log in to post new content in the forum.
