You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Makerbase (new) 84200hp 'quirky' on/off 'bug'? by flez1966 » Wed, 2024-03-20 17:06 |
3 |
by Huang_jh Thu, 2024-10-17 13:24 |
|
|
Flipsky BLDC motor reporting wrong rpm and cant use hall effects by TonyD » Fri, 2024-03-29 18:44 |
3 |
by TonyD Wed, 2024-04-03 16:06 |
|
|
Information about "Das RS" and "Das mini" hardware using DRV8313/DRV8320 by hexakopter » Thu, 2018-04-26 19:18 |
3 |
by hexakopter Wed, 2018-06-13 00:39 |
|
|
MICRO Module by F4metz » Sat, 2019-03-02 15:10 |
3 |
by chuttney1 Sun, 2019-03-03 18:54 |
|
|
Flipsky 4.12 Vesc in FOC mode? by Jonny254 » Sat, 2018-09-08 11:25 |
3 |
by Jonny254 Thu, 2018-09-13 05:48 |
|
|
Troubleshooting Newborn VESC by vadicus » Tue, 2019-04-09 02:13 |
3 |
by vadicus Tue, 2019-05-14 02:06 |
|
|
Flipsky Dual FSESC6.6 loses connection, connected BLDC buzzing after restart by gabrielredding » Mon, 2019-04-29 00:00 |
3 |
by Constantin00 Fri, 2021-09-17 11:00 |
|
|
Bus bar and heavy copper PCBs by lopezcontreras » Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
|
|
Mosfet Discussion by WalterWitt » Mon, 2022-04-18 20:38 |
3 |
by vadicus Thu, 2022-04-21 00:01 |
|
|
DIYElectricSkateboard.com Torque Board Street: DOA by epretorious » Thu, 2022-06-02 17:54 |
3 |
by frank Sat, 2022-06-04 11:50 |
|
|
Flipsky FSESC 4.12 Bluetooth over mini USB? by blaz.ferlic » Fri, 2021-11-19 10:18 |
3 |
by lurch Fri, 2021-11-19 14:00 |
|
|
Current Sensor by CTSchorsch » Fri, 2021-12-03 14:53 |
3 |
by R4850S1 Sat, 2021-12-04 08:57 |
|
|
200V +200A power stage and custom VESC controller with fault protection by ZombieSS » Sat, 2020-07-18 07:35 |
3 |
by mystamo Tue, 2020-07-28 22:07 |
|
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware » Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
|
|
MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s by mxpro32 » Sun, 2019-06-30 21:39 |
3 |
by TechAUmNu Tue, 2019-08-13 10:21 |
|
|
Motor detection accuracy in 3rd party hardware (old FW vs new FW) by shaman » Tue, 2020-02-25 16:03 |
3 |
by vadicus Wed, 2020-02-26 19:09 |
|
|
copy setup from one vesc to another? by curtm » Mon, 2019-07-08 20:33 |
3 |
by district9prawn Sat, 2019-07-20 23:44 |
|
|
config wanted, for 75100 with ebike geared hub motor by tom355 » Mon, 2023-02-20 09:51 |
3 |
by JanneHooo Sun, 2025-05-11 19:17 |
|
|
For sale: Paltatech VESC 150kW Adaptors and Logic Board 0.2 by albertocesare » Tue, 2019-03-05 10:45 |
4 |
by return97 Mon, 2022-12-19 17:25 |
|
|
Custom 12S VESC seems to be power limiting or something by nickw1881 » Sat, 2018-08-25 07:40 |
4 |
by nickw1881 Tue, 2018-09-18 05:56 |
|
|
Motor spins only with outside help by asaf123098 » Thu, 2019-04-04 06:52 |
4 |
by dekafive Thu, 2019-06-20 11:36 |
|
|
Flipsky VESC-clone firmware udapte problems by gui-rider » Sun, 2019-04-28 22:39 |
4 |
by avsha Fri, 2019-11-22 06:55 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
4 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
HW4.12 Firmware trouble by CTSchorsch » Wed, 2018-12-05 21:09 |
4 |
by sam.vanratt Fri, 2018-12-28 17:55 |
|
|
Custom VESC4.8 short circuit error by b4zz » Mon, 2018-12-17 10:26 |
4 |
by b4zz Wed, 2018-12-19 16:48 |
Log in to post new content in the forum.
