You are here
VESC Original Hardware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis » Fri, 2020-05-22 07:34 |
2 |
by TheFallen Wed, 2020-05-27 08:59 |
|
|
Servomotor control with VESC6 by Humberto Estrada » Wed, 2019-05-22 16:15 |
0 |
by Humberto Estrada Wed, 2019-05-22 16:15 |
|
|
Quala-T power switch keeps switching off by luuksteitner » Sat, 2024-04-20 08:38 |
0 |
by luuksteitner Sat, 2024-04-20 08:38 |
|
|
PWM outputs on Hall1 and Hall2 pins by brentfpage » Mon, 2020-08-31 01:32 |
2 |
by mechatronixNick Wed, 2021-01-27 08:53 |
|
|
Programming Vesc 4.12 motor spin only in detection mode by DanieleRA » Sun, 2019-07-28 16:29 |
0 |
by DanieleRA Sun, 2019-07-28 16:29 |
|
|
Problems reaching theoretical max (150k) ERPM on VESC6 by ignaciobfp » Sun, 2020-07-26 19:10 |
4 |
by ignaciobfp Fri, 2020-08-07 16:52 |
|
|
Power switch on VESCT6+ (MK3) by henry10210 » Thu, 2019-12-26 00:47 |
8 |
by henry10210 Tue, 2020-02-11 15:48 |
|
|
Power button works only as turn ON button, but not working as turn OFF by zmei116 » Tue, 2020-05-26 18:52 |
4 |
by electricfox Sat, 2024-03-09 18:57 |
|
|
Please help, problems with brand new vesc 6 pluss. by sabladask » Fri, 2023-05-05 15:08 |
0 |
by sabladask Fri, 2023-05-05 15:08 |
|
|
optimizing the set up to reduce mosfet heating by tromes » Tue, 2020-06-16 02:48 |
2 |
by TechAUmNu Sun, 2020-08-02 15:06 |
|
|
noise problem with VESC 6 Mk V by kylerlaird » Sun, 2021-02-28 01:04 |
0 |
by kylerlaird Sun, 2021-02-28 01:04 |
|
|
No throttle response by Bucket_Residence » Sat, 2022-05-14 16:57 |
16 |
by Gatze Fri, 2022-06-17 10:00 |
|
|
No power or Comm via USB by swedan » Fri, 2021-04-09 14:33 |
1 |
by vadicus Fri, 2021-04-09 19:52 |
|
|
nice solution 3x3 phase VESC out to 3 single motor wires by tobiokanobi » Tue, 2022-04-19 17:13 |
5 |
by tobiokanobi Mon, 2022-04-25 14:55 |
|
|
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto » Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
|
|
My original Vesc 6 plus is not working by kesigomu » Sat, 2020-12-05 15:51 |
0 |
by kesigomu Sat, 2020-12-05 15:51 |
|
|
Motor won’t run when VESC BMS is connected via CAN by Samuel Pernsteiner » Mon, 2025-03-24 11:42 |
1 |
by electricfox Mon, 2025-03-24 20:33 |
|
|
Mechanical dimensions of VESC 6 by ufechner » Sat, 2018-04-28 19:01 |
2 |
by TechAUmNu Mon, 2018-04-30 22:28 |
|
|
Iron less Axialflux Motor by tobiokanobi » Sat, 2019-03-30 12:11 |
8 |
by tobiokanobi Sat, 2025-11-15 20:57 |
|
|
Input Voltage on PPM (Servo) VESC6? by Marc Pflugmann » Fri, 2018-05-25 21:02 |
3 |
by Roger Wolff Thu, 2018-05-31 08:05 |
|
|
Inductance (L) measurement by rahmaev_a_o » Tue, 2018-08-07 10:10 |
4 |
by benjamin Sat, 2019-02-23 10:11 |
|
|
Independent external power for VESC 6 MK3? by henry10210 » Sun, 2020-08-02 00:27 |
1 |
by TheFallen Sun, 2020-08-02 16:11 |
|
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons » Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
|
|
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY » Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
|
|
HW 4.12 Change low voltage cutoff by subodh.malgonde » Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
Log in to post new content in the forum.
