You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Vesc 6 - Rotorposition control with Encoder AS5047P by Espeya24 » Thu, 2020-12-10 09:01 |
2 |
by DMajoe Tue, 2026-03-10 22:39 |
|
|
CAN not working on VESC MkV by chundri » Tue, 2021-01-12 15:06 |
2 |
by domi.8248 Mon, 2025-03-03 07:19 |
|
|
VESC 4.12 +5v output by lennarn » Tue, 2020-04-28 15:35 |
2 |
by sandrino Mon, 2023-01-23 16:01 |
|
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis » Fri, 2020-05-22 07:34 |
2 |
by thefallen Wed, 2020-05-27 08:59 |
|
|
VESC hw4.7 firmware update in vesc tool (2.06) fails with "Erase timed out" by snowcrazed » Thu, 2020-07-23 05:47 |
2 |
by Maxid Mon, 2025-05-12 10:27 |
|
|
Do you know how wire simultaneously bluetooth module and 9dof sensor? Bluetooth now connected to TX RX, but it is the same pins by zmei116 » Thu, 2020-08-27 18:02 |
2 |
by thefallen Sun, 2020-08-30 19:33 |
|
|
VESC75/300 USB Connection Issue by Gerhard » Fri, 2020-11-20 22:37 |
2 |
by Gerhard Tue, 2020-12-01 16:26 |
|
|
Change sensor voltage on latest VESC 75/300 MK IV by R04 » Sun, 2024-01-28 21:22 |
2 |
by frank Fri, 2024-02-23 15:39 |
|
|
Does Trampa BMS work with multiple VESCs? by kylerlaird » Sun, 2025-04-20 03:57 |
2 |
by kylerlaird Sun, 2025-04-20 15:38 |
|
|
VESC 100/250 Bluetooth not showing up by JumpinJackFlash » Sun, 2022-10-09 19:03 |
2 |
by JumpinJackFlash Tue, 2022-10-11 17:27 |
|
|
Vesc motor resistance value by HiandHello » Wed, 2023-02-15 07:45 |
2 |
by HiandHello Wed, 2023-02-15 22:57 |
|
|
Ground Housing VESC by T18m26 » Mon, 2023-04-17 16:25 |
2 |
by T18m26 Thu, 2023-04-27 08:28 |
|
|
VESC MAXIM+120 Reverse Button by michael.jahrer » Wed, 2026-04-22 21:32 |
2 |
by michael.jahrer Sun, 2026-04-26 18:56 |
|
|
Dual Vesc6 setup: Vesc with nrf no blue light by Paul15578 » Sat, 2017-11-04 04:00 |
2 |
by Paul15578 Mon, 2017-11-06 13:56 |
|
|
BLDC control in FOC mode by da_rul0r » Fri, 2019-08-16 15:32 |
2 |
by sanketh1691 Fri, 2021-11-05 19:05 |
|
|
VESC 75/300 current noise / losing sync? by ezonca » Thu, 2019-10-03 23:06 |
2 |
by benjamin Thu, 2019-10-10 07:56 |
|
|
Hall count drift by xachmo » Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
|
|
VESC 6 Plus reseting settings and firmware by granstubbe » Fri, 2020-01-10 18:31 |
2 |
by ozcankosar Fri, 2022-11-25 22:18 |
|
|
Charging through phase wires by jesusc » Mon, 2021-01-18 21:14 |
2 |
by jesusc Thu, 2021-06-03 02:17 |
|
|
optimizing the set up to reduce mosfet heating by tromes » Tue, 2020-06-16 02:48 |
2 |
by TechAUmNu Sun, 2020-08-02 15:06 |
|
|
VESC 75/300 as generator inverter troubleshooting by Renco » Thu, 2020-06-18 13:10 |
2 |
by Renco Wed, 2020-06-24 08:50 |
|
|
VESC 75 300 R2 - correct battery conection by SafrdA » Fri, 2021-04-30 13:13 |
2 |
by frank Wed, 2021-05-26 11:19 |
|
|
VESC 75/250 v 75/300? by AliBarrett10 » Tue, 2021-07-06 19:50 |
2 |
by Ht Tue, 2021-10-12 07:08 |
|
|
PWM outputs on Hall1 and Hall2 pins by brentfpage » Mon, 2020-08-31 01:32 |
2 |
by mechatronixNick Wed, 2021-01-27 08:53 |
|
|
VESC 75 precharge by wagner » Fri, 2020-09-18 22:16 |
2 |
by wagner Tue, 2020-09-22 16:01 |
Log in to post new content in the forum.
