You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Speed Pin from motor into VESC 6+? by dfelz » Tue, 2020-04-07 23:42 |
1 |
by frank Mon, 2020-05-04 14:50 |
|
|
Vesc 4.10 high amp blocks motor by darowi » Sun, 2024-03-10 18:22 |
1 |
by rafeh1 Fri, 2024-10-11 01:10 |
|
|
75300 IV Trampa schematic by MangoK » Tue, 2024-12-10 13:11 |
1 |
by Foujiwara Mon, 2025-03-17 04:38 |
|
|
VESC HD60 Single version by lacondro » Tue, 2022-05-31 07:37 |
1 |
by frank Tue, 2022-05-31 07:48 |
|
|
StartUp in OpenLoop with Duty Control really jerky by tobiokanobi » Thu, 2022-09-29 07:22 |
1 |
by frank Thu, 2022-09-29 08:00 |
|
|
Vesc Pronto Hall Sensors not detecting by lcappellano » Sun, 2026-01-11 19:27 |
1 |
by electricfox Mon, 2026-01-12 11:40 |
|
|
Trampa 100/250 with Cyc X1 Pro motor by Asi » Mon, 2023-05-22 17:33 |
1 |
by vadicus Thu, 2023-06-01 21:31 |
|
|
Differences between V75 300, V75 300 R2, and R3 by Jason_no1 » Wed, 2023-08-09 05:55 |
1 |
by Jason_no1 Wed, 2023-08-09 05:57 |
|
|
Flipsky 75200 Pro suddenly stops working by terente » Thu, 2023-12-28 20:53 |
1 |
by elektrobekaniq Sat, 2024-08-03 11:44 |
|
|
Driving two motors with 75/300 by cmarc » Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
|
|
VESC design specification, manual by velolac » Thu, 2020-01-02 15:54 |
1 |
by velolac Sat, 2020-01-11 00:05 |
|
|
Different HW versions for V6?! by Marc Pflugmann » Sun, 2018-06-24 13:43 |
1 |
by frank Mon, 2018-06-25 13:01 |
|
|
Using ABI Encoders by danielw » Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
|
|
Vesc 6.4 has 80A continuous current. Is that battery or motor? by MaxMaker1 » Mon, 2020-03-02 23:35 |
1 |
by velolac Sun, 2020-03-29 17:51 |
|
|
Smoked 3 month old VESC - What did I do wrong? by cjjohnson97 » Thu, 2020-04-16 02:30 |
1 |
by velolac Sun, 2020-08-02 11:27 |
|
|
Can you flash VESC Hardware with BLheli firmware? by saliraza.ai » Fri, 2021-02-26 20:38 |
1 |
by TheFallen Mon, 2021-03-01 16:31 |
|
|
vesc 3.3 or 5v is shorted to GND by fer-bo » Fri, 2021-03-05 14:57 |
1 |
by fer-bo Fri, 2021-03-05 18:24 |
|
|
No power or Comm via USB by swedan » Fri, 2021-04-09 14:33 |
1 |
by vadicus Fri, 2021-04-09 19:52 |
|
|
VESC VI plus - No usable power / under voltage fault after pwr delivery by velolac » Sun, 2020-07-12 19:37 |
1 |
by velolac Sat, 2020-08-29 21:51 |
|
|
switch/toggle between two different engine settings/characteristics by Lasse » Tue, 2020-12-29 23:18 |
1 |
by skyline1970 Sun, 2021-02-07 17:35 |
|
|
VESC HD60 schematic by junho912 » Wed, 2024-04-03 10:55 |
1 |
by h1989 Tue, 2024-11-05 19:13 |
|
|
VESC Encoder connected to 12v by yanting Liu » Fri, 2022-04-29 07:53 |
1 |
by frank Sat, 2022-04-30 14:24 |
|
|
usb is not connecting by asnamp » Wed, 2022-05-18 09:00 |
1 |
by frank Thu, 2022-05-19 17:14 |
|
|
Motor won’t run when VESC BMS is connected via CAN by Samuel Pernsteiner » Mon, 2025-03-24 11:42 |
1 |
by electricfox Mon, 2025-03-24 20:33 |
|
|
VESC mating signal connectors by Jogitech » Mon, 2022-09-05 14:44 |
1 |
by frank Thu, 2022-09-08 08:04 |
Log in to post new content in the forum.
