You are here
VESC Original Hardware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Collection of Burned 100/250 Vesc´s by xenon321 » Thu, 2021-07-01 17:39 |
38 |
by electricfox Wed, 2023-10-18 18:21 |
|
|
Controlling multiple VESC over SPI by ttufuor » Mon, 2019-11-18 04:37 |
2 |
by Danny Bokma Fri, 2020-01-24 18:29 |
|
|
corupted firmware by Johnnylamouette » Fri, 2021-04-16 05:53 |
0 |
by Johnnylamouette Fri, 2021-04-16 06:31 |
|
|
Current measuring with DRV amplifiers by PXSS » Mon, 2018-02-12 03:14 |
5 |
by lizardmech Fri, 2018-03-02 00:43 |
|
|
Danger to go more than 100% duty cycle during downhill ? by f.damien12 » Thu, 2022-03-24 14:12 |
3 |
by skyline1970 Sat, 2022-03-26 09:29 |
|
|
Different HW versions for V6?! by Marc Pflugmann » Sun, 2018-06-24 13:43 |
1 |
by frank Mon, 2018-06-25 13:01 |
|
|
Disable throttle while braking This topic has been moved to "General discussion" (View topic) |
|||
|
Do you know how wire simultaneously bluetooth module and 9dof sensor? Bluetooth now connected to TX RX, but it is the same pins by zmei116 » Thu, 2020-08-27 18:02 |
2 |
by TheFallen Sun, 2020-08-30 19:33 |
|
|
Driving two motors with 75/300 by cmarc » Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
|
|
DRV8302 Gate drive limitations by nickw1881 » Sun, 2018-04-29 09:56 |
0 |
by nickw1881 Sun, 2018-04-29 09:56 |
|
|
dual VESC battery current by chris_winkel » Tue, 2019-06-18 15:26 |
0 |
by chris_winkel Tue, 2019-06-18 15:26 |
|
|
Dual VESC sync problem by Svenska Svenson » Wed, 2017-10-18 18:56 |
4 |
by Svenska Svenson Sat, 2017-10-28 13:47 |
|
|
Dual Vesc6 setup: Vesc with nrf no blue light by Paul15578 » Sat, 2017-11-04 04:00 |
2 |
by Paul15578 Mon, 2017-11-06 13:56 |
|
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl » Tue, 2019-05-28 14:48 |
0 |
by Jackl Tue, 2019-05-28 14:48 |
|
|
fault_code_high_offset_current_sensor_1 by Enak » Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
|
|
Flashing via SWD works, but no green LED or USB enumeration by vpl » Fri, 2018-11-16 17:48 |
1 |
by vpl Wed, 2018-11-21 17:27 |
|
|
FSESC 6.6 dual short on 3.3v on 1 side by vic1234 » Thu, 2022-02-17 22:33 |
4 |
by vic1234 Fri, 2022-02-18 17:52 |
|
|
Getting RPM data from VESC 4.12 by EmirDns » Wed, 2022-01-05 21:20 |
0 |
by EmirDns Wed, 2022-01-05 21:20 |
|
|
Ground Housing VESC by T18m26 » Mon, 2023-04-17 16:25 |
2 |
by T18m26 Thu, 2023-04-27 08:28 |
|
|
Hall count drift by xachmo » Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
|
|
Hall sensor not working by Stupidspencer » Sat, 2019-12-28 20:29 |
4 |
by BeliaEllet Wed, 2021-03-31 17:55 |
|
|
HARDWARE QUESTION: Maximum AC voltage VESC can tolerate? by danvel » Fri, 2018-04-27 15:31 |
4 |
by Roger Wolff Mon, 2018-05-14 22:13 |
|
|
HD60 CAN Resistor by BEWA » Wed, 2021-04-21 14:56 |
0 |
by BEWA Wed, 2021-04-21 14:56 |
|
|
Higher voltage DRV error by jarrow » Tue, 2018-03-06 10:06 |
0 |
by jarrow Tue, 2018-03-06 10:06 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
Log in to post new content in the forum.
