You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Pictures from "Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller"? by timmertens » Thu, 2022-06-16 17:56 |
1 |
by frank Thu, 2022-06-16 19:47 |
|
|
Taking 5-6 seconds for running motor under ADC mode by asnamp » Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
|
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
|
VESC Tool Crashing on connection (on Macbook version) by svelte.ca » Thu, 2025-07-31 00:00 |
2 |
by etavav Thu, 2025-09-18 17:19 |
|
|
Update 0.87 impossible by vpower » Thu, 2018-01-18 13:17 |
2 |
by arvidb Thu, 2018-01-18 17:07 |
|
|
ADC Connector is very touchy by ebikerevolution » Wed, 2018-05-09 20:30 |
2 |
by TechAUmNu Tue, 2018-05-15 10:46 |
|
|
Android & usb by TONY61 » Mon, 2025-02-10 12:48 |
2 |
by TONY61 Wed, 2025-02-12 14:54 |
|
|
High Current Sampling Mode True 80% current by antonchromjak » Sun, 2017-09-24 21:14 |
2 |
by antonchromjak Wed, 2017-09-27 19:59 |
|
|
More detail in tool tips by TechAUmNu » Mon, 2018-07-23 20:15 |
2 |
by TechAUmNu Tue, 2018-07-24 13:52 |
|
|
Motor setup help please by TrevM » Wed, 2017-12-13 17:11 |
2 |
by nickw1881 Wed, 2018-03-21 05:42 |
|
|
VESC not connecting by jetomit » Wed, 2020-05-20 16:08 |
2 |
by Kent Tabor Sat, 2020-10-17 15:48 |
|
|
vesc UART with arduino 33 BLE by amaussa » Mon, 2020-10-12 16:57 |
2 |
by Seb44120 Fri, 2020-11-20 23:06 |
|
|
Understanding FOC Wizard Innerworkings by gravity99 » Thu, 2022-08-18 22:24 |
2 |
by gravity99 Mon, 2022-08-22 15:23 |
|
|
Please Help.. VESC Tool 6.02 starts, but window won't open. by KJB » Tue, 2023-05-23 07:44 |
2 |
by edilger Mon, 2024-07-01 10:25 |
|
|
Detection failed. Reason: Flux linkage detection failed by Donnyten » Sun, 2022-10-09 20:31 |
2 |
by Donnyten Tue, 2022-10-11 02:56 |
|
|
Vesc Tool on Carplay - We need a display! by modman » Tue, 2023-03-28 16:10 |
2 |
by wraven Fri, 2024-06-21 16:18 |
|
|
"bad detection result received" impossible to achieved motor detection ! by titimomotete » Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
|
|
VESC Tool 0.95 App by einbi » Tue, 2018-10-09 11:02 |
2 |
by Yanick Hautecoeur Thu, 2021-09-30 13:55 |
|
|
Flipsky nrf51288 by Idoff » Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
|
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu » Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
|
|
Autodetection algorithm by Griffen » Thu, 2019-01-03 18:44 |
2 |
by Gmack Fri, 2020-09-18 16:39 |
|
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
|
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan » Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
|
|
FOC detection not working, "L=0" by chundri » Tue, 2021-01-12 15:02 |
2 |
by chundri Wed, 2021-01-13 15:40 |
Log in to post new content in the forum.
