You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning » Mon, 2024-12-02 13:19 |
0 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
|
|
Vesc tool app not installed on Samsung a02s by Zuky » Sun, 2025-08-03 20:31 |
0 |
by Zuky Sun, 2025-08-03 20:32 |
|
|
Flipsky FSESC 6.7PRO and bluetooth module by phonkie » Mon, 2025-08-18 06:33 |
0 |
by phonkie Mon, 2025-08-18 06:33 |
|
|
lispBM command "gpio-hold" by Jamesavery22 » Sat, 2025-01-04 20:46 |
0 |
by Jamesavery22 Sat, 2025-01-04 20:46 |
|
|
Battery profiles? by ahagge » Mon, 2025-09-01 16:36 |
0 |
by ahagge Mon, 2025-09-01 16:36 |
|
|
Odys Alpha X3 Pro Settings by flashice » Mon, 2025-01-06 14:28 |
0 |
by flashice Mon, 2025-01-06 14:34 |
|
|
turn counter by player107 » Wed, 2025-09-10 22:52 |
0 |
by player107 Wed, 2025-09-10 22:52 |
|
|
Urgent Help Connecting TS5700N8501-like Magnetic Encoder by jumana » Tue, 2025-01-14 19:37 |
0 |
by jumana Tue, 2025-01-14 19:37 |
|
|
limited mode by Satrio » Fri, 2025-09-26 16:31 |
0 |
by Satrio Fri, 2025-09-26 16:31 |
|
|
Vesc Tool 6.06 test version 2 error by NOAI » Sat, 2025-01-25 13:00 |
0 |
by NOAI Sat, 2025-01-25 13:00 |
|
|
PID Speed Control Type by User18 » Fri, 2025-10-31 19:35 |
0 |
by User18 Fri, 2025-10-31 19:35 |
|
|
Very low Flux Linkage calulation FOC,General Tab - 0.0xx mWb by kjjajsdASHD » Sun, 2025-02-02 13:59 |
0 |
by kjjajsdASHD Sun, 2025-02-02 13:59 |
|
|
VESC Tool IMU Problem by 13.meshhi » Sun, 2025-11-16 23:40 |
0 |
by 13.meshhi Sun, 2025-11-16 23:40 |
|
|
How I disconnect CAN communation between two ESCs in dual channel ESC by Adesh Kute » Tue, 2025-12-16 08:10 |
0 |
by Adesh Kute Tue, 2025-12-16 08:10 |
|
|
Detection for a drone outrunner 515 kV and 775 kV by MaksK » Thu, 2020-06-04 16:05 |
0 |
by MaksK Thu, 2020-06-04 16:05 |
|
|
Inappropriate ioctl by Roger Wolff » Sat, 2018-06-02 17:38 |
0 |
by Roger Wolff Sat, 2018-06-02 18:04 |
|
|
Motor starting while flasing firmware by RSR » Sun, 2017-09-17 15:31 |
0 |
by RSR Sun, 2017-09-17 15:31 |
|
|
Terminal Command for Current? by Mannerow » Thu, 2020-10-29 23:07 |
0 |
by Mannerow Thu, 2020-10-29 23:07 |
|
|
ESC State, Switch Value, and Motor Position unknown by 175_pilot » Wed, 2020-11-04 04:22 |
0 |
by 175_pilot Wed, 2020-11-04 04:22 |
|
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 » Mon, 2020-07-06 03:09 |
0 |
by bmwman91 Mon, 2020-07-06 03:21 |
|
|
Vesc 6, FW 5.1, WH charged is not being logged by BalorNG » Thu, 2020-12-03 14:19 |
0 |
by BalorNG Thu, 2020-12-03 14:19 |
|
|
Data Loggin Values by BLeaCH » Sat, 2020-04-04 07:37 |
0 |
by BLeaCH Sat, 2020-04-04 07:37 |
|
|
Running a DC 12V trolling motor with a 4.20. Hidden current limit?. by Impuls60 » Wed, 2020-07-22 14:32 |
0 |
by Impuls60 Wed, 2020-07-22 19:00 |
|
|
Motor detection failed/ 0 faults by jnweb29 » Sat, 2017-12-23 21:07 |
0 |
by jnweb29 Sat, 2017-12-23 21:07 |
|
|
ADC MAX Voltage 5volt ? by liteglow » Sat, 2020-07-25 23:48 |
0 |
by liteglow Sat, 2020-07-25 23:48 |
Log in to post new content in the forum.
