You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
vesc tool not opening by RemyMade413 » Sat, 2026-02-28 12:15 |
2 |
by mariuszdymon Sat, 2026-02-28 23:07 |
|
|
Please Help.. VESC Tool 6.02 starts, but window won't open. by KJB » Tue, 2023-05-23 07:44 |
2 |
by edilger Mon, 2024-07-01 10:25 |
|
|
Detection failed. Reason: Flux linkage detection failed by Donnyten » Sun, 2022-10-09 20:31 |
2 |
by Donnyten Tue, 2022-10-11 02:56 |
|
|
motor max rpm and current severely limited? by Roy Zhang » Mon, 2021-08-09 19:23 |
2 |
by vadicus Thu, 2021-08-12 04:06 |
|
|
Overheating protection, voltage-/current-limitation etc. by kianK » Thu, 2021-04-15 07:23 |
2 |
by lilliamhoyle Wed, 2021-07-07 09:36 |
|
|
Problem | Documentation images not showing by nadav182 » Mon, 2021-10-04 19:54 |
2 |
by lopezharding Wed, 2022-09-21 10:50 |
|
|
FOC detection not working, "L=0" by chundri » Tue, 2021-01-12 15:02 |
2 |
by chundri Wed, 2021-01-13 15:40 |
|
|
Реверс вращения двигателя by Wolod5 » Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
|
|
VESC Tool on Windows 10 32 Bit doesn't open by Red_Speedster » Mon, 2021-05-31 16:33 |
2 |
by frank Wed, 2022-01-26 08:21 |
|
|
RPM increase by Tibor Kalman Za... » Tue, 2021-02-23 10:12 |
2 |
by Tibor Kalman Za... Sat, 2021-02-27 21:41 |
|
|
Speed control by dent » Tue, 2020-03-10 20:11 |
2 |
by dent Wed, 2020-03-11 02:49 |
|
|
Possible to use a e-scooter brake as a Gas lever? by max1102 » Fri, 2019-11-08 07:59 |
2 |
by max1102 Mon, 2019-11-18 21:25 |
|
|
FAILED DETCTION. REASON:-11,and FAULT_CODE_DRV by marco esteban l... » Wed, 2019-12-11 01:40 |
2 |
by marco esteban l... Wed, 2019-12-11 18:54 |
|
|
PPM Configuration is Only Working While Connected to VESC Software by kyle45 » Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
|
|
Servo Control PPM by jonthie » Tue, 2020-01-28 15:04 |
2 |
by IanG Thu, 2020-04-16 11:42 |
|
|
Vesc Tool Mobile can't update Vesc Firmware by Happy Giraffe » Wed, 2022-01-19 21:48 |
2 |
by Happy Giraffe Thu, 2022-01-20 23:50 |
|
|
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes » Fri, 2024-05-03 20:30 |
2 |
by rafeh1 Wed, 2024-11-06 09:14 |
|
|
RT Data, v3.01, Amazon Fire Tablet (sideloaded) by j.konrad » Thu, 2022-02-24 14:51 |
2 |
by j.konrad Fri, 2022-02-25 14:14 |
|
|
VESC runs only with 50% duty cycle by Nimrod0201 » Wed, 2024-07-10 18:30 |
2 |
by Nimrod0201 Sat, 2024-07-13 11:34 |
|
|
Hall sensor problems by Traceo » Wed, 2021-11-10 00:05 |
2 |
by Traceo Fri, 2021-11-19 22:35 |
|
|
beginners by viniii00 » Tue, 2021-11-23 20:12 |
2 |
by FOURDAN Mon, 2022-07-04 10:13 |
|
|
brake switch/brake regen question by smallbikefun » Sat, 2024-04-06 01:48 |
2 |
by smallbikefun Sun, 2024-04-14 22:08 |
|
|
Duty Cycle Mode - limited ZERO RPM duty cycle by maheshK » Mon, 2021-11-29 11:24 |
2 |
by frank Tue, 2021-11-30 07:46 |
|
|
Switch between different modes via remote by Cledus » Sun, 2017-10-22 13:56 |
2 |
by MatwoSvK Tue, 2017-11-07 22:32 |
|
|
FOC configuration when resistance is measured as R=0. by Roger Wolff » Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
Log in to post new content in the forum.
