You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Vesctool otg by meashman » Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
|
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS » Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
|
|
Firmware issues by salvasalce » Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
|
|
Motor whine with HFI? by christopher.h.poole » Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
|
|
Connect VESC to Keyboard/Wireless Joystick by sanketh1691 » Mon, 2021-10-04 20:58 |
2 |
by sanketh1691 Wed, 2021-10-06 18:58 |
|
|
VESC TOOL cant connect to hardware by svs » Sat, 2021-04-24 22:06 |
2 |
by jose carceller Sun, 2022-08-21 00:43 |
|
|
PPM Configuration is Only Working While Connected to VESC Software by kyle45 » Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
|
|
motor to slow and no power by Thiery Vardon » Sat, 2021-01-09 10:45 |
2 |
by Thiery Vardon Tue, 2021-01-12 13:27 |
|
|
Servo Control PPM by jonthie » Tue, 2020-01-28 15:04 |
2 |
by IanG Thu, 2020-04-16 11:42 |
|
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas » Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
|
|
Use Vesc-Tool to run two motors simultaneously via CAN by microlomaniac » Thu, 2021-06-17 11:55 |
2 |
by spacewalker Tue, 2021-06-22 08:23 |
|
|
Speed control by dent » Tue, 2020-03-10 20:11 |
2 |
by dent Wed, 2020-03-11 02:49 |
|
|
Software safety features interrupting normal operation. by Tsomo » Wed, 2021-07-14 01:29 |
2 |
by Tsomo Wed, 2021-07-14 01:32 |
|
|
Possible to use a e-scooter brake as a Gas lever? by max1102 » Fri, 2019-11-08 07:59 |
2 |
by max1102 Mon, 2019-11-18 21:25 |
|
|
current control via CAN not working by STTS » Thu, 2021-08-12 11:51 |
2 |
by mm_iem Mon, 2021-08-30 18:00 |
|
|
Question about FOC Wizard by proget.snc » Thu, 2021-08-26 16:31 |
2 |
by proget.snc Thu, 2021-09-02 14:23 |
|
|
FAILED DETCTION. REASON:-11,and FAULT_CODE_DRV by marco esteban l... » Wed, 2019-12-11 01:40 |
2 |
by marco esteban l... Wed, 2019-12-11 18:54 |
|
|
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes » Fri, 2024-05-03 20:30 |
2 |
by rafeh1 Wed, 2024-11-06 09:14 |
|
|
VESC runs only with 50% duty cycle by Nimrod0201 » Wed, 2024-07-10 18:30 |
2 |
by Nimrod0201 Sat, 2024-07-13 11:34 |
|
|
brake switch/brake regen question by smallbikefun » Sat, 2024-04-06 01:48 |
2 |
by smallbikefun Sun, 2024-04-14 22:08 |
|
|
Writing to slave vesc sometimes cause loss of can bus by meashman » Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
|
|
Writing value to both VESCs on FocFox Unity by agraham » Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
|
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota » Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
|
|
Vesc Tool For Mac by kmfpod » Tue, 2022-06-14 22:06 |
2 |
by nic sandiland Sun, 2025-09-21 18:21 |
|
|
VESC Tool Crashing on connection (on Macbook version) by svelte.ca » Thu, 2025-07-31 00:00 |
2 |
by etavav Thu, 2025-09-18 17:19 |
Log in to post new content in the forum.
