You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Active braking without regen current by stoibinger » Mon, 2025-03-17 14:17 |
0 |
by stoibinger Mon, 2025-03-17 14:17 |
|
|
Abs over current error by ogp » Sat, 2025-03-15 22:12 |
0 |
by ogp Sat, 2025-03-15 22:12 |
|
|
[SOLVED] COMM_GET_VALUES on top of COMM_FORWARD_CAN not working by yes_wecangogreen » Sun, 2025-03-09 12:48 |
1 |
by yes_wecangogreen Wed, 2025-03-12 10:22 |
|
|
Wrong software shows up. Answered my own question. by leecon » Fri, 2025-03-07 17:50 |
1 |
by leecon Tue, 2025-03-11 17:00 |
|
|
Motor amps by TONY61 » Sun, 2025-02-16 12:37 |
1 |
by Groundspeed100 Tue, 2025-03-11 16:20 |
|
|
Erpm effect on power. by TONY61 » Mon, 2025-02-10 10:28 |
1 |
by Groundspeed100 Tue, 2025-03-11 16:13 |
|
|
Help with understanding/using PID control by Groundspeed100 » Tue, 2025-03-11 15:58 |
0 |
by Groundspeed100 Tue, 2025-03-11 16:01 |
|
|
Advice needed: How to select KV value (or: how important is KV, in reality?) by c0d3z3r0 » Tue, 2024-09-03 09:23 |
3 |
by Groundspeed100 Tue, 2025-03-11 15:23 |
|
|
vesc throttle response by TONY61 » Tue, 2025-02-04 16:20 |
5 |
by Groundspeed100 Mon, 2025-03-10 20:23 |
|
|
75300 make high pitch after close power switch by Kaeomangkon » Sat, 2025-03-08 11:37 |
0 |
by Kaeomangkon Sat, 2025-03-08 11:37 |
|
|
Understanding Dual VESC (dual motors) setups by Cham » Mon, 2020-09-21 18:45 |
6 |
by hemmadroid Thu, 2025-03-06 06:34 |
|
|
bldc motor calibration issue by Thejesh Bollineni » Sat, 2025-03-01 00:15 |
0 |
by Thejesh Bollineni Sat, 2025-03-01 00:15 |
|
|
75200 3.3 or 5v short circuit after 10 mins of use by Vassily » Thu, 2025-02-27 23:26 |
0 |
by Vassily Thu, 2025-02-27 23:26 |
|
|
Updated firmware on duel hd60 now one wont turn on by Hippydeathcult » Thu, 2025-02-27 11:10 |
0 |
by Hippydeathcult Thu, 2025-02-27 11:10 |
|
|
Connect multiple VESC over CAN bus by Anthony20 » Tue, 2025-02-25 02:58 |
1 |
by electricfox Thu, 2025-02-27 07:08 |
|
|
Dual controller: turn left and right by coolic » Tue, 2025-02-25 13:01 |
1 |
by electricfox Thu, 2025-02-27 07:05 |
|
|
low speed / high friction startup, max torque by schnedan » Mon, 2025-02-24 10:18 |
0 |
by schnedan Mon, 2025-02-24 10:19 |
|
|
Flipsky screen for Ubox driver help! by Dostawca.L » Sat, 2025-02-22 19:20 |
0 |
by Dostawca.L Sat, 2025-02-22 19:20 |
|
|
Stop motor after certain number of rounds by Gawarmel » Wed, 2025-02-19 12:51 |
0 |
by Gawarmel Wed, 2025-02-19 12:51 |
|
|
VESC with large motor by ppet36 » Sat, 2025-02-15 17:28 |
1 |
by ppet36 Sun, 2025-02-16 19:33 |
|
|
Nothing works for MY1020 3kw 72v motor and flipsky75100 by Valérian Pigeon » Tue, 2025-02-04 16:49 |
4 |
by Valérian Pigeon Thu, 2025-02-06 20:59 |
|
|
vesc on android by TONY61 » Wed, 2025-02-05 14:00 |
1 |
by TONY61 Thu, 2025-02-06 16:08 |
|
|
Overvoltage Error during setup by arranto12 » Mon, 2021-11-08 23:22 |
4 |
by electricfox Tue, 2025-02-04 19:28 |
|
|
How to achieve synchronize position control by CAN between 2 VESCs by ztwsa007 » Sat, 2019-07-06 17:32 |
2 |
by mansi712 Tue, 2025-02-04 14:37 |
|
|
PPM+UART. RC and esp32 by coldreboot » Thu, 2025-01-30 23:20 |
0 |
by coldreboot Fri, 2025-01-31 15:50 |
Log in to post new content in the forum.
